Plasterboard with fire resistant additives
Suitable for drylining most internal wall and ceiling applications where increased levels of fire protection is required including garages, fire escape routes, seperating floors and steele encasements.
Can be used for direct decoration or plaster finish.
Has a pink paper face for easy identification on site.
Available in both tapered edge or square edge finishes.
Achieves 'Very Good' rating under BES 6001
Thicknesses and Availability:
Available in 12.5mm and 15mm thicknesses.
Available in most popular sizes at most depots; short lead-times may apply if we need to get stock in before delivering to site.
General information about Gyproc Fireline
Dry lining plasterboard
British Gypsum's plasterboard, Gyproc Fireline, is suitable for drylining most internal wall and ceiling applications where higher levels of fire protection is required. It is suitable for direct decoration or plaster finish.
Gyproc Fireline consists of anaerated gypsum core with glass fibre and other additives encased in, and firmly bonded to, strong paper liners
Pink paper on the front face while the hidden face is a brown paper
|Thermal Conductivity||0.025 W/m·K|
|Nominal Density||780 - 784 kg/m³|
|Board Length||2.4 - 3m|
|Board Width||0.9 & 1.2m|
|Board Edge||Tapered or Square|
Buy Gyproc Fireline
Reasonable stock levels are generally held at most of our depots. In some geographic locations, depots may stock alternates, however, we will contact you to discuss before proceeding with the order.
Where products need to be brought in from British Gypsum, please allow approx. 2 week for delivery.
Please observe the 'Star Rating' indicators to assess availability.
Generally 1 or 2 days for delivery
Generally 1 to 5 days for delivery
Generally 5 to 10 days for delivery
Generally 5 to 15 days for delivery
Please call to check availability and approximate lead times
Product availability depends upon stock levels at closest depot and delivery logistics to geographic locations
Product Performance and Guides
Product Performance, Manufacturer Certification, Downloads, and Installation Guides
While we have provided information for all sizes of Gyproc Fireline, some board sizes may not be readily available and carry minimum order requirements.
Gyproc Fireline 12.5mm: Weight = 9.8 kg/m², Density = 784 kg/m³, Thermal Conductivity = 0.024 W/m·K and Thermal Restistance = 0.05 m²K/W
Gyproc Fireline 15mm: Weight = 11.7 kg/m², Density = 780 kg/m³, Thermal Conductivity = 0.024 W/m·K and Thermal Restistance = 0.06 m²K/W
Items highlighted in green are generally held in stock at our depots.
|Gyproc Fireline 12.5mm||0.9m||1.8m||T/E & S/E|
|Gyproc Fireline 12.5mm||1.2m||2.4m||T/E & S/E|
|Gyproc Fireline 12.5mm||1.2m||2.7m||T/E|
|Gyproc Fireline 12.5mm||1.2m||3m||T/E|
|Gyproc Fireline 15mm||0.9m||1.8m||T/E|
|Gyproc Fireline 15mm||0.9m||1.8m||T/E|
|Gyproc Fireline 15mm||1.2m||2.4m||T/E & S/E|
|Gyproc Fireline 15mm||1.2m||2.7m||T/E|
|Gyproc Fireline 15mm||1.2m||3m||T/E|
Standards & Approval
EN 520: 2004 + A1: 2009 Gypsum plasterboards, definitions, requirements and test methods.
Type F: Gypsum plasterboard with improved core adhesion at high temperatures. Plasterboard with a face to which suitable gypsum plasters or decoration may be applied. These boards have mineral fibres and/or other additives in the gypsum core to improve core cohesion at high temperatures.
It is important to observe appropriate health and safety legislation when working on site i.e. personal protective clothing and equipment, etc. The following notes are intended as general guidance only. In practice, consideration must be given to design criteria requiring specific project solutions.
This product may be cut using a plasterboard saw or by scoring with a sharp knife and snapping the board over a straight edge. Holes for switch or socket boxes should be cut out before the boards are fixed using a utility saw or sharp knife. When cutting boards, power and hand tools should be used with care and in accordance with the manufacturers’ recommendations. Power tools should only be used by people who have been instructed and trained to use them safely. Appropriate personal protective equipment should be used.
Fix boards with decorative side out to receive joint treatment or a skim plaster finish. Lightly butt boards together. Never force boards into position. Install fixings not closer than 13mm from cut edges and 10mm from bound edges. Position cut edges to internal angles whenever possible, removing paper burrs with fine sandpaper. Stagger horizontal and vertical board joints between layers by a minimum of 600mm. Locate boards to the centre line of framing where this supports board edges or ends.
The face (pink) of Gyproc FireLine can be plastered with either Thistle Board Finish or Thistle Multi-Finish. There should be a minimum delay between completion of the lining and the commencement of plastering.
Gyproc jointing materials produce durable joint reinforcement and a smooth, continuous, crack-resistant surface ready for priming and final decoration. A number of jointing specifications are available to suit the board type, method of application, and site preference.
After the joint treatment has dried, decoration, including any decorator’s preparatory work, should follow with the minimum delay.